Digital LG plus Series Guia de preparacion Pagina 173
- Pagina / 186
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
173
W
warm start A reboot or soft reset. The following occurs:
1) data are cleared from all buffers (I/O and internal print
buffers); 2) all internal system variables are reset to
default values, which is transparent to the user; and 3)
the power-up configuration values-except the host I/O
selection-are loaded. If the user has not defined power-
up configuration values, the printer resets to the factory
default configuration values.
weight See character weight.
write To store data to memory (RAM) or to mass storage (hard
disk, floppy diskette, etc.).
X
X-OFF A character transmitted by the printer announcing that
the printer is off-line or the buffer is almost full.
X-ON A character transmitted by the printer announcing that
the printer is on-line or the buffer is almost empty.
- Setup Guide 1
- Trademark Acknowledgments 4
- Table of Contents 5
- 1 Overview 9
- Printer Emulations 11
- Host Computer Interfaces 11
- Graphics Enhancement Option 13
- Taking Care of Your Printer 13
- LinePrinter Plus Features 13
- Protocols and Emulations 14
- Line Matrix Printing 15
- Printing Speed 16
- 2 Setting Up the Printer 17
- Chapter 2 Before You Begin 18
- Select a Site 19
- Printer Component Locations 20
- Remove the Cardboard Packing 21
- Foam Strips (2) 22
- Hammer Bank 22
- Protective Foam 22
- Tractor Door 22
- Tractor Lock 22
- Platen Protective Foam 23
- Forms Thickness Lever 23
- Support Shaft 23
- Adjust the Paper Supports 24
- Release the Paper Chains 25
- Remove the Tags 26
- Forms Thickness 29
- Platen Protective 29
- Remove Tag 31
- Attach the Output Basket 32
- Install Basic Components 34
- Install the Ribbon 36
- April 27, 2001 38
- May 1, 2001 39
- August 15, 2000 39
- Load the Paper 40
- Paper Scale 42
- Splined Shaft 42
- Power On the Printer 44
- Set the Top-of-Form 45
- IMPORTANT 47
- Test the Printer 48
- 3 Configuring the Printer 49
- Chapter 3 Overview 50
- Operating Modes 52
- The Control Panels 52
- ENTER SWITCH 53
- UNLOCKED 53
- Changing Parameters 55
- Chapter 3 Changing Parameters 56
- Saving Your New Configuration 57
- Deleting Your Configuration 59
- Loading Configuration Values 63
- The Power-Up Configuration 65
- 4 The Configuration Menus 67
- Chapter 4 Overview 68
- Configuration Main Menu 69
- CONFIG. CONTROL 70
- Save Config 71
- Print Config 71
- Delete Config 71
- Power-Up Config 71
- Protect Configs 71
- ACTIVE EMULATION 72
- EMULATION 73
- Digital LG 74
- Vert. Forms 75
- Horiz. Forms 75
- Autowrap 76
- CR (Carriage Return) 76
- LF (Line Feed) 76
- Unsolicited Rpt 76
- Print Mode Opt 77
- Plot Mode Opt 77
- I-2/5 Guard Bars 77
- LinePrinter+ 78
- Printer Protocol 79
- Print Char Set 79
- CPI/LPI Select 79
- Font Attributes 79
- Page Format 81
- Proprinter XL Emulation 82
- Define LF Code 83
- FF Valid at TOF 83
- Character Set 83
- Alternate Char Set 83
- 20 CPI Condensed 83
- Epson FX Emulation 84
- P-Series Emulation 86
- Select SFCC 88
- EVFU Select 88
- Alt. Set 80-9F 88
- SFCC d Command 88
- IGP/PGL Emulation 89
- Define LF Code (Line Feed) 90
- PI Slew Range 90
- Select Font 91
- Select LPI 91
- Auto Uppercase 91
- Skip Command Prefix 92
- Power On IGP/PGL 92
- Extended Execute Copy 92
- UPC Descenders 92
- Compressed CPI 92
- Ignore Character 93
- IGP100 Compatbl 93
- Optimized Ratio 93
- IGP/VGL Emulation 94
- SFCC & Pwrup 95
- Graphics Options 96
- Chapter 4 IGP/VGL Emulation 98
- Error Handling 99
- Ignore / DB8 Setup 100
- Font Set 101
- PI Control 101
- MAINT / MISC 102
- HOST INTERFACE 103
- Serial Submenu 104
- Stop Bits 105
- Baud Rate 105
- Word Length 105
- Data Terminal Ready 106
- Request to Send 106
- Buffer Size in K 106
- Parallel Submenu 107
- Dataproducts Submenu 109
- Data Bit 8 109
- PI Ignored 109
- Data Polarity 109
- Data Request Polarity 110
- Strobe Polarity 110
- Bidirectional Submenu 111
- PRINTER CONTROL 112
- Slow Paper Slew 113
- Power Saver Time 113
- DIAGNOSTICS 114
- Test Width 115
- Paper Out Dots 115
- System Memory 115
- Print Statistics 116
- RIBBONMINDER 117
- Ribbon Size 118
- Ribbon Adjust 118
- Fault Action 118
- 5 Interfaces 119
- Centronics Parallel Interface 122
- Removal and Installation 125
- IEEE 1284 Parallel Interface 126
- The Negotiation Phase 127
- RS-232 and RS-422 132
- RS-232 only 132
- VMS Operating System 133
- 6 Routine Service and 135
- Interior Cleaning 137
- Diagnosing Problems 138
- Printer Self-Tests 139
- Printing a Hex Dump 140
- Fault Messages 142
- Chapter 6 Diagnosing Problems 144
- 7 RibbonMinder 149
- Using the RibbonMinder 150
- Configuration 151
- Running a Job 152
- New Ribbon 152
- Ribbon Action 153
- RibbonMinder Fault 154
- A Printer Specifications 157
- Printer Dimensions 158
- Environmental Characteristics 158
- Electrical Characteristics 159
- Interfaces 159
- Printing Rates 160
- B Standard ASCII Character 161
- Appendix B 162
- C Printronix Technical 163
- Printronix Technical Support 164
- D Glossary 165
- Appendix D 166
- This is 14 point type 170
- 172292-001B 186
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales